{"id":21412,"date":"2025-09-01T16:09:36","date_gmt":"2025-09-01T14:09:36","guid":{"rendered":"https:\/\/silla.industries\/docs\/prism-howto-configurazione-guidata\/"},"modified":"2025-09-12T15:19:45","modified_gmt":"2025-09-12T13:19:45","password":"","slug":"prism-howto-configurazione-guidata","status":"publish","type":"docs","link":"https:\/\/silla.industries\/en\/docs\/prism-howto-configurazione-guidata\/","title":{"rendered":"Guided Configuration"},"content":{"rendered":"\n<h1 class=\"wp-block-heading\">Introduction<\/h1>\n\n<p class=\"wp-block-paragraph\">The <strong>Configuration<\/strong> Wizard (also called the configuration &#8220;Wizard&#8221;) is the procedure that guides the user in configuring the parameters of Prism after finishing its installation.<\/p>\n\n<h1 class=\"wp-block-heading\">Guided Configuration<\/h1>\n\n<p class=\"wp-block-paragraph\">After powering up Prism, make sure there are no error LEDs, then proceed with the configuration wizard.<\/p>\n\n<div class=\"warning\">\nIn the case of red LEDs, refer to the &#8220;LEDs&#8221; section to check that the installation was done properly.\n<\/div>\n\n<h2 class=\"wp-block-heading\">Access the Configuration Wizard<\/h2>\n\n<p class=\"wp-block-paragraph\">To access the wizard, you need to connect to the Prism WiFi network and visit the configuration page.<\/p>\n\n<ul class=\"wp-block-list\">\n<li>Connect to Prism&#8217;s Wi-Fi network. In case you are using a smartphone, turn off the cellular data network as a precaution.<\/li>\n<\/ul>\n\n<div class=\"note\">\nThe WiFi network name and password can be found in the credentials label located in the manual that came with Prism.\n<\/div>\n\n<figure class=\"wp-block-image aligncenter size-full is-resized\"><a href=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/IMG-prism_wifi_SSD-542.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"542\" height=\"606\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/IMG-prism_wifi_SSD-542.jpg\" alt=\"Prism wifi SSD detail\" class=\"wp-image-15163\" style=\"width:271px;height:303px\" srcset=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/IMG-prism_wifi_SSD-542.jpg 542w, https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/IMG-prism_wifi_SSD-542-268x300.jpg 268w, https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/IMG-prism_wifi_SSD-542-360x403.jpg 360w\" sizes=\"auto, (max-width: 542px) 100vw, 542px\" \/><\/a><\/figure>\n\n<ul class=\"wp-block-list\">\n<li>Once connected, open the browser and go to the page <strong><a href=\"http:\/\/192.168.8.1\/benvenuto\" target=\"_blank\" rel=\"noreferrer noopener\">http:\/\/192.168.8.1\/<\/a> <\/strong>and press on Settings (from Smartphone, open the drop-down menu in the upper right corner)<\/li>\n<\/ul>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-17.png\" alt=\"\" class=\"wp-image-16896\"\/><\/figure>\n\n<ul class=\"wp-block-list\">\n<li>On the login page, enter the &#8220;installer&#8221; credentials.<\/li>\n<\/ul>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-18.png\" alt=\"\" class=\"wp-image-16900\"\/><\/figure>\n\n<div class=\"note\">\nThe &#8220;installer&#8221; credentials can be found in the credentials label placed in the manual that came with Prism.\n<\/div>\n\n<h2 class=\"wp-block-heading\">Prism configuration<\/h2>\n\n<p class=\"wp-block-paragraph\">The first page of the Guided Configuration contains the operating parameters of Prism.<\/p>\n\n<h3 class=\"wp-block-heading\"><strong>Type of installation<\/strong><\/h3>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-16.png\" alt=\"\" class=\"wp-image-16893\"\/><\/figure>\n\n<p class=\"wp-block-paragraph\">The first information to be provided is the type of installation, which can be:<\/p>\n\n<ul class=\"wp-block-list\">\n<li><strong>Single Prism<\/strong>\n<ul class=\"wp-block-list\">\n<li>For installation of only one Prism on the system.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n<ul class=\"wp-block-list\">\n<li><strong>Main prism (cluster)<\/strong><\/li>\n\n\n\n<li><strong>Secondary prism (cluster)<\/strong>\n<ul class=\"wp-block-list\">\n<li>Use these options for installation of multiple Prisms on the same system.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n<div class=\"warning\">\n<b>The configurations for Single Prism will be given<\/b> below. For the configuration of a Prism Cluster, follow the <b><a href=\"https:\/\/silla.industries\/docs\/prism-cluster\/\">Cluster Guide<\/a><\/b>. \n<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Electrical system system: number of phases<\/strong><\/h3>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-15.png\" alt=\"\" class=\"wp-image-16890\"\/><\/figure>\n\n<p class=\"wp-block-paragraph\">Select type of plant on which the Prism is installed, which can be:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>Single-phase<\/li>\n\n\n\n<li>Two-phase*<\/li>\n\n\n\n<li>Three-phase<\/li>\n<\/ul>\n\n<div class=\"warning\">\n* For <b>two-phase systems<\/b>, it may be necessary to install a transformer upstream of the Prism power line, as not all cars can charge on a two-phase system. Ask the dealer about it and give it a test charge.\n<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Circuit breaker calibration<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Select the corresponding value in amperes (A) of the size of the circuit breaker protecting the Prism power line:<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-12.png\" alt=\"\" class=\"wp-image-16879\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\"><strong>Meter power<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Enter the value in watts (W) corresponding to the contracted power supplied by the household meter:<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-11.png\" alt=\"\" class=\"wp-image-16876\"\/><\/figure>\n\n<div class=\"example\">\n<b>Example:<\/b> if the meter is 3kW, enter &#8220;3000&#8221; as the value.\n<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Sensor downstream of the meter<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Select <strong>YES <\/strong>if the Prism sensor, which is essential for managing load balancing, has been installed:<\/p>\n\n<ol class=\"wp-block-list\">\n<li>Select the type of sensor installed by choosing from <strong>100A <\/strong>(standard) or <strong>1000A <\/strong>(for large-cut systems, which <a href=\"https:\/\/silla.industries\/set-di-sensori-1000a\/\">can be ordered from our shop <\/a>as an optional accessory).<\/li>\n\n\n\n<li>After verifying that the value read by the sensor matches what is delivered by the meter, check &#8220;Yes, I have verified and the two values match.&#8221;<\/li>\n<\/ol>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-10.png\" alt=\"\" class=\"wp-image-16873\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\"><strong>MID sensor presence<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Set the drop-down menu to <strong>YES <\/strong>if a compatible MID sensor has been connected to Prism (optional, see this <a href=\"https:\/\/silla.industries\/es\/docs\/prism-dialoga-con-dei-meter-esterni-diversi-dallo-smart-meter\/\">FAQ<\/a> about this):<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-9.png\" alt=\"\" class=\"wp-image-16870\"\/><\/figure>\n\n<p class=\"wp-block-paragraph\">Check the next item if you want Prism to continue to receive data via its internal sensor if the MID fails.<\/p>\n\n<h3 class=\"wp-block-heading\"><strong>Powerwall storage device presence<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Select <strong>YES <\/strong>if you want to enable API communication with a Tesla Powerwall. Enter the required values in the fields: <\/p>\n\n<ul class=\"wp-block-list\">\n<li>IP address of the Powerwall.<\/li>\n\n\n\n<li>Powerwall login email.<\/li>\n\n\n\n<li>Tesla Gateway Password<\/li>\n<\/ul>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-8.png\" alt=\"\" class=\"wp-image-16867\"\/><\/figure>\n\n<div class=\"example\">\nThis functionality may be discontinued if updates are applied by the Tesla manufacturer.\n<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Load balancing<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Set the drop-down menu to <strong>YES <\/strong>if you want to enable load balancing. Values should then be selected via the respective drop-down menus: <\/p>\n\n<ul class=\"wp-block-list\">\n<li>Data source:\n<ul class=\"wp-block-list\">\n<li>  Sensor installed<\/li>\n\n\n\n<li>Powerwall<\/li>\n<\/ul>\n<\/li>\n\n\n\n<li>Presence of photovoltaic system: NO\/YES.<\/li>\n\n\n\n<li>Arera Experimentation: NO\/YES<\/li>\n<\/ul>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-7.png\" alt=\"\" class=\"wp-image-16864\"\/><\/figure>\n\n<div class=\"example\">\nARERA experimentation gives 5.5kW + 10% tolerance to reach 6kW.\nThe sensor detects the current flow at the point of contact, but if the potential difference (voltage) in the cables is lower in Prism than that measured at the meter there can be power detection differences of a few hundred watts which then, by setting 6000 with ARERA, can cause the meter to disconnect.\nAlways set the value to 5500 for safety.<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Autostart<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Select the charging start mode:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>Automatic charging startup <strong>is<\/strong> allowed<\/li>\n\n\n\n<li><strong>No. Allow only thumb drives and Silla cards<\/strong>  Requires the swipe of an RFID card provided by Silla<\/li>\n\n\n\n<li><strong>No. Also allow the use of generic cards<\/strong>  Allows authorization with any RFID card with <strong>mifare<\/strong> protocol<\/li>\n<\/ul>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-6.png\" alt=\"\" class=\"wp-image-16861\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\"><strong>Remote access<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Enable remote access in order to use Prism through the MySilla application.<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-5.png\" alt=\"\" class=\"wp-image-16858\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\">Communication via <strong>OCPP<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">In this section you can enter parameters to connect Prism to a Central System OCPP. Follow the <strong><a href=\"https:\/\/silla.industries\/es\/docs\/prism-howto-ocpp\/\">dedicated guide <\/a><\/strong>for all the details: <\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-4.png\" alt=\"\" class=\"wp-image-16855\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\">Automatic Updates<\/h3>\n\n<p class=\"wp-block-paragraph\">Select whether you want Prism to update automatically<strong>(Yes<\/strong>) or through manual authorization<strong>(No<\/strong>)<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-3.png\" alt=\"\" class=\"wp-image-16852\"\/><\/figure>\n\n<div class=\"note\">\nPress <b>Next<\/b> and proceed to the next screen of the Configuration Wizard.\n<\/div>\n\n<h2 class=\"wp-block-heading\">Network configuration<\/h2>\n\n<p class=\"wp-block-paragraph\">This page shows all the parameters of the network configuration.<\/p>\n\n<div class=\"warning\">\nConfigurations for &#8220;Single Prism&#8221; mode installations are given. for Cluster installations follow the dedicated <a href=\"https:\/\/silla.industries\/docs\/prism-cluster\/\">Cluster<\/a> guide. \n<\/div>\n\n<h3 class=\"wp-block-heading\"><strong>Current local network settings<\/strong><\/h3>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-1.png\" alt=\"\" class=\"wp-image-16846\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\"><strong>Connecting to a WiFi network<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">Press on the WiFi network to which Prism is to be connected, enter the password, and press <strong>Connect<\/strong>:<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image.png\" alt=\"\" class=\"wp-image-16843\"\/><\/figure>\n\n<h3 class=\"wp-block-heading\"><strong>Remote access testing<\/strong><\/h3>\n\n<p class=\"wp-block-paragraph\">In this part, it is possible to check the <strong>connection status of<\/strong> Prism and communication with Silla servers for using cloud services such as <strong>MySilla<\/strong> and receiving updates:<\/p>\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" src=\"https:\/\/silla.industries\/wp-content\/uploads\/2023\/05\/image-2.png\" alt=\"\" class=\"wp-image-16849\"\/><\/figure>\n\n<div class=\"note\">\nPress on <b>&#8220;Save and Close&#8221;<\/b> to finish the configuration.\n<\/div>\n\n<p class=\"wp-block-paragraph\"><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Introduction The Configuration Wizard (also called the configuration &#8220;Wizard&#8221;) is the procedure that guides the user in configuring the parameters<\/p>\n","protected":false},"author":34,"featured_media":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"doc_category":[],"doc_tag":[1671,560,1694],"class_list":["post-21412","docs","type-docs","status-publish","hentry","doc_tag-how-to-en","doc_tag-prism-en","doc_tag-wi-fi-en"],"year_month":"2026-10","word_count":856,"total_views":"27","reactions":{"happy":"0","normal":"0","sad":"0"},"author_info":{"name":"veroweb","author_nicename":"veroweb","author_url":"https:\/\/silla.industries\/en\/author\/veroweb\/"},"doc_category_info":[],"doc_tag_info":[{"term_name":"How to...","term_url":"https:\/\/silla.industries\/en\/docs-tag\/how-to-en\/"},{"term_name":"Prism","term_url":"https:\/\/silla.industries\/en\/docs-tag\/prism-en\/"},{"term_name":"Wi-Fi","term_url":"https:\/\/silla.industries\/en\/docs-tag\/wi-fi-en\/"}],"knowledge_base_info":[],"knowledge_base_slug":[],"_links":{"self":[{"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/docs\/21412","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/docs"}],"about":[{"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/types\/docs"}],"author":[{"embeddable":true,"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/users\/34"}],"replies":[{"embeddable":true,"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/comments?post=21412"}],"version-history":[{"count":0,"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/docs\/21412\/revisions"}],"wp:attachment":[{"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/media?parent=21412"}],"wp:term":[{"taxonomy":"doc_category","embeddable":true,"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/doc_category?post=21412"},{"taxonomy":"doc_tag","embeddable":true,"href":"https:\/\/silla.industries\/en\/wp-json\/wp\/v2\/doc_tag?post=21412"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}